Titanium Concentrate Grades, TiO2 Basis and Procurement Checks
Leave a message
Titanium Concentrate: What the Material Actually Is
Titanium concentrate is the beneficiated mineral product from which almost every titanium value stream begins. It is produced by crushing, grinding, gravity separation, magnetic separation and flotation of titanium-bearing sand or hard-rock ore, and it is delivered as a dry, free-flowing granular solid rather than as a chemical compound. The commercial importance of a concentrate is decided by four things at once: the titanium dioxide (TiO2) grade, the level and form of iron, the gangue and trace-element profile, and the particle size distribution that the receiving plant can feed.
Because the concentrate is a mineral commodity and not a finished metal, two buyers of the same tonnage can be buying very different materials. A sulfate-route pigment plant, a chloride-route chlorinator, a ferrotitanium furnace and a welding consumable producer each screen the same shipment against different limits. This article sets out the grade families, the specification items that appear on a certificate of analysis, the conversion routes, and the procurement and acceptance rules that a technical buyer should apply when comparing offers for titanium concentrate.
Grade Families from Ilmenite to Rutile
Naturally occurring titanium minerals fall into a small number of families, and the concentrate trade is organised around them.
Ilmenite is iron titanium oxide, nominally FeTiO3, with a theoretical TiO2 content of about 52%. Commercial ilmenite concentrates are traded over a broad band, most commonly a lower grade suitable for the sulfate pigment route and an upgraded grade for chlorination or for slag smelting.
Leucoxene is an altered, iron-depleted ilmenite in which TiO2 has been enriched by weathering. It sits between ilmenite and rutile and is often an intermediate product of beach-sand operations.
Natural rutile is close to pure TiO2 and is the highest-grade feedstock for chlorination, with very low iron.
Titanium slag is not mined but smelted: ilmenite plus a carbon reductant in an electric furnace yields a titanium-rich slag and a pig-iron co-product. Slag grades are usually described as acid-soluble or high-titanium depending on the intended downstream route.
Synthetic rutile is produced by leaching iron out of ilmenite, giving a rutile-like product intermediate between upgraded ilmenite and natural rutile.
For procurement purposes, the practical question is never "is this titanium concentrate" but "which route will this parcel feed, and does its analysis and sizing match that route".
Typical Grade Bands and Chemical Specification
The table below summarises the ranges normally cited when titanium feedstocks are classified commercially. Exact contractual limits are always set by the supply agreement and verified by assay; the bands below are the conventional order of magnitude for each family.
| Product form | Typical TiO2 | Iron level | Usual sizing | Principal route |
|---|---|---|---|---|
| Ilmenite concentrate, standard grade | about 44-50% | high, FeO/Fe2O3 dominant | 0.1-0.5 mm sand, or ground fines | Sulfate pigment route; titanium slag feed |
| Ilmenite concentrate, upgraded grade | about 54-60% | reduced iron | 0.1-0.4 mm | Slag smelting; some chloride feed |
| Leucoxene | about 65-90% | low iron | 0.1-0.3 mm | Chloride route blending |
| Titanium slag, acid-soluble | about 74-80% | low, residual FeO | 0-2 mm or fine ground | Sulfate pigment route |
| Titanium slag, high-titanium | about 85-92% | very low | 0.1-1.5 mm coarse | Chloride route |
| Synthetic rutile | about 90-95% | very low | 0.1-0.5 mm | Chloride route |
| Natural rutile | about 92-96% | very low | 0.1-0.6 mm | Chloride route, welding electrodes |
Trace and gangue elements matter as much as the TiO2 headline figure. Chromium oxide is tolerated poorly in chloride feedstocks because it forms volatile chlorides that contaminate titanium tetrachloride; alkaline earth oxides raise the chlorinator residue load and the acid demand in the sulfate route; phosphorus and sulphur are watched in both pigment and metallurgical chains; and uranium and thorium, naturally associated with heavy mineral sands, are monitored because of transport and dose-rate requirements.
A concentration report is therefore read as a package: TiO2 and total iron first, then SiO2, Al2O3, MnO, MgO, CaO, Cr2O3, V2O5, P, S, moisture, and the radionuclide declaration that many ports require for heavy-mineral cargoes. Buyers should request the previous three shipment assays of the same lot or a similar lot, since mineral concentrate grades drift as a deposit is mined block by block.
From Concentrate to Metal and Pigment
Three industrial routes consume titanium concentrate, and each one imposes its own acceptance rules.
Sulfate pigment route. Ilmenite or acid-soluble slag is digested in concentrated sulphuric acid, the resulting titanium sulfate solution is clarified and hydrolysed, and the hydrated oxide is calcined, milled and surface-treated to give pigmentary titanium dioxide. Because this route dissolves the whole feed, it accepts relatively high iron and alkaline earth contents, but it consumes acid stoichiometrically, so acid-soluble slag is attractive where acid cost and waste neutralisation dominate.
Slag smelting. Ilmenite is smelted with a carbon reductant in a submerged-arc furnace. Iron oxides reduce to metallic iron, which is tapped as a pig iron co-product, while TiO2 reports to a molten slag that is cooled and crushed. Feed selection centres on the TiO2 to iron ratio, the reductant reactivity and the electrical load stability of the furnace.
Chloride route. High-grade feedstock is chlorinated with chlorine in the presence of coke in a fluidised bed to give titanium tetrachloride, which is purified by distillation and condensation. The tetrachloride is either oxidised back to pigment or reduced with magnesium to sponge titanium and then vacuum-arc or electron-beam melted. Chlorination is a dry, relatively selective process: coarse, low-alkaline, low-chromium feed with consistent sizing fluidises well, while excessive fines create dust carry-over and excessive calcium and magnesium increase the chloride waste stream.
The metallurgical route is shorter. Ferrotitanium is made by aluminothermic or silicothermic reduction of titanium-bearing feed, and the alloy is used for deoxidation, for grain refinement and for fixing nitrogen and carbon in certain steels. Ferrotitanium is covered by the GB/T 3282 family of designations, with commonly traded classes spanning approximately 25-35%, 35-45% and 65-75% titanium; the standard fixes the exact content ranges and impurity limits for each class, so a certificate should quote the class plus the measured analysis rather than a generic figure.
Downstream Uses and the Grade They Demand
Pigmentary titanium dioxide remains the dominant volume outlet, and pigment quality is regulated by international specifications such as ISO 591-1 and ASTM D476, which classify pigment by crystal form, minimum TiO2 content and required performance properties. Chloride-route pigment normally requires a purer feedstock than the sulfate route, which is why rutile, high-titanium slag and synthetic rutile carry a structural premium over standard ilmenite.
Sponge titanium production consumes far less tonnage but demands the strictest feed quality, since residual elements follow through to the melting stage. Sponge titanium itself is graded under GB/T 2524, with grades running from MHTi-0 through the higher-numbered grades as minimum titanium falls and iron, oxygen, nitrogen and hardness limits widen. Mill products derived from that sponge are specified under grade designations of the GB/T 3620.1 system, for example TA1, TA2 and TA3 for industrial pure titanium and TC4 for the Ti-6Al-4V alloy, and tubular products are commonly ordered against ASTM B338, ASTM B861 and ASME SB338 for the Grade 1, Grade 2, Grade 7, Grade 9 and Grade 12 chemistries used in heat exchangers and condensers. Sheet, strip and plate are ordered against ASTM B265.
Welding consumables, flux-cored and coated electrode coatings, and steel degassing additions consume rutile and ferrotitanium in combination, where the requirement is low phosphorus, low sulphur and consistent sizing rather than the highest possible TiO2.
Sampling, Assay and Moisture
Assay disputes almost always trace back to sampling, not to laboratory method. For bulk mineral products the sampling and sample preparation procedure should follow the GB/T 2007 series for bulk mineral products, and where the parcel is treated as a ferroalloy-type consignment, ISO 3713 or GB/T 4010 give the corresponding sampling rules. A sound contract specifies: sample increment count and mass, sampling location during loading or unloading, sample preparation method, retained duplicate samples, an umpire laboratory, and the binding status of the loading-port analysis against the discharge-port analysis.
Moisture is the second most common source of disagreement. Mineral concentrates are shipped with residual moisture that varies with the dewatering circuit and the season, so the weight basis must be explicit. Three conventions appear in contracts: wet metric tonne, dry metric tonne, and a conditioned weight where moisture above an agreed base is deducted. The determination method, the sample drying temperature and the number of replicates should all be written into the agreement, and the moisture result should be issued alongside the dry-basis chemical analysis so that the buyer can convert the two without assumptions.
Elemental determinations should be made by a laboratory working to a recognised analytical method and reporting the method reference, the instrument used, the duplicate spread and the detection limits. For pigment-grade feedstocks, colour and brightness-related parameters may also be specified, since concentrate characteristics influence the optical performance of the finished pigment.
Sizing, Packaging, Storage and Transport
Sizing is a functional specification, not a cosmetic one. Fluidised-bed chlorination wants a narrow, coarse cut with minimal ultrafines; sulfate digestion tolerates a much wider distribution including fine grinding; slag furnaces accept a coarse feed. Buyers should therefore state the nominal size range, the permissible oversize and undersize, and the screen test method, rather than accepting a verbal description of the material as sand or lumps.
Packaging follows the destination. Mineral sands and slags are commonly shipped in lined one-tonne flexible intermediate bulk containers, in 25 kg or 50 kg woven bags for smaller metallurgical consumers, or as bulk cargo in a vessel hold. Where the material is sold as a ferroalloy-type addition, packaging should follow the GB/T 3650 convention for ferroalloys, with the bag or drum marked by grade, lot number and net weight. Particle size requirements for ferroalloy-type products are addressed jointly with GB/T 13247, and the same principles of declared size range and screened verification apply to concentrates sold to metallurgical customers.
Concentrates must be stored dry and segregated by lot. Cross-contamination between a high-chromium and a low-chromium parcel is expensive to correct and is a frequent cause of rejection at the chlorinator. Silo and stockpile hygiene, loader cleanliness and the condition of container liners should be inspected before loading. Heavy-mineral cargoes also attract port-level scrutiny: a radiation screening declaration, expressed as a measured surface dose rate and a specific activity statement, is a normal document for ilmenite, leucoxene, rutile and zircon-bearing parcels, and a shipment should not be booked without confirming that the receiving port accepts the declared values.
How a Titanium Concentrate Offer Is Structured
Titanium concentrate is not quoted on an exchange in the way that some refined metals are; offers are negotiated contract by contract and are structured around a quality-linked base. Understanding that structure is more useful to a buyer than any single day's number, because a headline number without its basis cannot be compared with another supplier's number.
The base variable is the TiO2 grade, usually expressed as a minimum percentage on a dry basis, with a stated penalty and bonus mechanism for deviations. The second variable is the impurity package: chromium oxide, alkaline earth oxides, phosphorus, sulphur and, for some routes, uranium and thorium all translate into process cost at the receiving plant, and a concentrate with a poor impurity profile is worth less even at the same TiO2. The third variable is size distribution and expected fines content. The fourth is moisture, because freight is paid on wet weight in many trades. The fifth is packaging and inland logistics. The sixth is the commercial frame: FOB, CFR or CPT, Incoterms edition, port of loading, vessel size, laycan, inspection agency at loading, weight and quality final at loading or discharge, and the currency and payment instrument.
A workable comparison therefore puts every offer onto the same footing before any number is examined. The disciplined sequence is: convert all offers to a dry metric tonne basis at a common Incoterm; normalise the TiO2 grade to the contract base with the agreed penalty and bonus schedule; subtract the estimated cost of dealing with out-of-specification impurities; add the cost of any extra packaging or handling; and only then compare the resulting net cost of contained titanium dioxide per unit of product actually recoverable in the buyer's own process. The buyer should also verify the supplier's ability to reproduce the assay shipment after shipment, because a single attractive parcel followed by a drifting grade is more expensive than a slightly higher price with a stable, documented quality.
Finally, the offer should be accompanied by, or reference, a documented quality system and a traceable lot numbering scheme. For concentrate specifically, the documents that matter in practice are the certificate of analysis with method references, the moisture determination, the radiation screening declaration, the packing list with lot numbers, and evidence that sampling was witnessed by an independent party where the contract requires it.
Common Misconceptions
"All ilmenite is interchangeable." Two ilmenite concentrates at the same TiO2 can behave completely differently in a chlorinator because of chromium, alkaline earth and size differences.
"Higher TiO2 always means a better buy." A very high-grade feedstock that is too fine, or that carries unacceptable chromium, can cost more per tonne of recoverable product than a coarser mid-grade parcel.
"Moisture is a minor correction." On a large parcel, a one or two percent difference in shipped moisture is a real tonnage of contained TiO2, and the weight basis decides who pays for it.
"Concentrate is a commodity with a standard price." Titanium feedstock pricing is contractual, quality-linked and route-specific; it cannot be read off a single index.
"Ferrotitanium and titanium concentrate are graded the same way." Ferrotitanium is an alloy specified by class under GB/T 3282, while concentrate is a mineral specified by TiO2 and impurities on a dry basis.
FAQ
Q: What TiO2 content is typical for a standard grade of ilmenite concentrate?
Standard ilmenite concentrate is commonly offered in the region of 44-50% TiO2 on a dry basis, and the exact contract limit is set between buyer and seller, with a stated penalty and bonus for deviation. Upgraded ilmenite sits higher, generally around 54-60% TiO2.
Q: Why do pigment plants distinguish between acid-soluble and high-titanium slag?
Acid-soluble slag dissolves in the sulfate digestion circuit and is priced against the acid and neutralisation cost of that route, while high-titanium slag is a lower-iron, higher-TiO2 product intended for chlorination and for downstream oxidation or reduction to titanium tetrachloride.
Q: Which impurities matter most for the chloride route?
Chromium oxide is the most damaging single impurity because it forms volatile species that contaminate the purified titanium tetrachloride, and calcium and magnesium oxides are also tightly limited because they increase the chlorinator waste stream and consume chlorine. Uranium and thorium are monitored for transport and dose-rate reasons.
Q: How is the weight of a titanium concentrate parcel determined?
Weight is normally established by draft survey of the vessel or by calibrated weighing at the loading facility, and the contract must state whether the final weight is wet or dry and where moisture is sampled. Dry weight is obtained by applying the moisture determination to the wet weight, so the sampling procedure for moisture is as important as the chemical assay.
Q: How does titanium concentrate relate to ferrotitanium and titanium sponge?
Titanium concentrate is the upstream feedstock. Ferrotitanium, specified by class under the GB/T 3282 family for the relevant titanium content band, is an alloy made by thermitic reduction and used in steelmaking. Titanium sponge, graded under GB/T 2524, is produced by chlorination of high-grade feedstock followed by magnesium reduction and is the raw material for titanium mill products.
Q: What documents should accompany a titanium concentrate shipment?
A certificate of analysis referencing the analytical methods used, a moisture determination on a dry-weight basis, a radiation screening declaration with the measured dose-rate statement, a packing list showing lot numbers and net weights, and the commercial documents matching the agreed Incoterm. Where the contract calls for independent verification, the loading inspection certificate and a retained umpire sample reference should be included.
