Home - Knowledge - Details

Classification of Silicon Carbide Powder: Grades, Crystal Forms and Sizing Systems

Grade Classification: Black, Green and Metallurgical

The first level of classification is by purity, because purity decides which crystal form predominates and therefore which applications are possible. Metallurgical silicon carbide at 88-90% SiC is used as a deoxidiser and as a furnace additive. Black silicon carbide, produced from quartz sand and petroleum coke in an electric resistance furnace at roughly 2200-2500 C, normally reaches 97-98.5% SiC and is tough rather than sharp, which suits grinding cast iron and non-ferrous metals. Green silicon carbide, made from a purer charge with salt added to the furnace mix, reaches 98.5-99% and above, has higher friability and is preferred for hard materials such as cemented carbide and for refractories that must resist oxidation.

Grade SiC content Colour Typical use
Metallurgical 88-90% Dark, dull Deoxidiser, furnace additive
Black 97-98.5% Black, iridescent Bonded and coated abrasives for cast iron
Green 98.5-99%+ Green Hard-metal grinding, refractories, ceramics

Crystal Form: Alpha and Beta Silicon Carbide

Silicon carbide crystallises in two families. Beta silicon carbide has a cubic structure and forms at lower synthesis temperatures, while alpha silicon carbide is hexagonal or rhombohedral and dominates the material produced at furnace temperatures above about 2000 C. Commercial abrasive and refractory powders are therefore almost entirely alpha silicon carbide in the 6H and 4H polytypes, with a small beta fraction appearing in very fine powder grades produced by milling or by vapour-phase routes. The distinction matters for technical ceramics, because the polytype influences sintering behaviour and the resulting fracture toughness.

Grit and Powder Sizing Systems

Coarse abrasive grain is designated with F numbers covering F4 to F220 under FEPA 42-1, and the corresponding ISO description of grain size distribution is given in ISO 8486-1 for macrogrits. Coated abrasive grains use the P series from P12 to P2500 under FEPA 43-1, with the distribution described in ISO 8486-2 for microgrits. Microgrits are specified by a median particle size d50 with a tolerance; typical values are about 29.2 micrometres for F320, 9.3 micrometres for F600 and 3.0 micrometres for F1200. A supplier and a buyer who quote only an F or P number are still not fully aligned until the d50 and the permitted oversize fraction are written into the order.

Designation System Typical d50 Application
F60 to F220 FEPA 42-1 / ISO 8486-1 Coarse to medium Bonded wheels, blasting media
P240 to P1200 FEPA 43-1 / ISO 8486-2 Medium to fine Coated abrasives, lapping
F320 to F1200 ISO 8486-2 29.2 to 3.0 micrometres Precision finishing, ceramics

Chemical Composition Control

Beyond the headline silicon carbide figure, four impurities are controlled: free carbon from unreacted coke, free silicon from incomplete reaction, iron as Fe2O3 from the charge and from milling media, and silica as SiO2 from surface oxidation. Chemical analysis of abrasive silicon carbide follows ISO 9286, which covers the determination of these constituents and provides a common basis for certificates. Powder for technical ceramics or for semiconductor-related use needs tighter limits again, because iron picked up during jet milling can exceed the specification even when the furnace product was clean.

Physical Properties Relevant to Selection

Silicon carbide has a Mohs hardness of 9 to 9.5 and a Knoop hardness near 2500 kg/mm2, a density of about 3.21 g/cm3, a coefficient of thermal expansion near 4.0 x 10-6 per kelvin and a thermal conductivity around 120 W per metre kelvin at room temperature. These values explain its use in kiln furniture and refractory plates where thermal shock resistance matters, and in seals and nozzles where wear resistance dominates. The material oxidises slowly in air above about 1200 C with a protective silica layer, and it decomposes near 2830 C, so service limits are usually set by the oxidation behaviour rather than by melting.

Frequently Asked Questions

Q: What is the practical difference between black and green silicon carbide powder?
A: Green material carries 98.5-99% SiC and fractures more readily, so it holds a sharp edge on hard workpieces, while black material at 97-98.5% is tougher and better suited to cast iron and non-ferrous grinding.

Q: Which standard defines the F and P grit sizes?
A: FEPA 42-1 covers F4 to F220 and FEPA 43-1 covers P12 to P2500, with the corresponding particle size distributions described in ISO 8486-1 for macrogrits and ISO 8486-2 for microgrits.

Q: Why does a certificate need a d50 value as well as a grit number?
A: Because the grit number alone does not fix the median particle size or the permitted oversize fraction, and two powders with the same F number can behave differently in a lapping or polishing operation.

Q: How is the chemical composition of silicon carbide powder tested?
A: ISO 9286 covers chemical analysis of abrasive silicon carbide, reporting silicon carbide content together with free carbon, free silicon, iron as Fe2O3 and silica as SiO2.

Q: Can metallurgical silicon carbide be substituted for abrasive grades?
A: No. At 88-90% SiC it contains too much free carbon and iron and its hardness and consistency are unsuitable for bonded or coated abrasive products; it belongs in deoxidation and furnace duties.

Send Inquiry

You Might Also Like