Silicon Carbide Grades, Properties and Price Formation
Leave a message
What Silicon Carbide Is and Why One Price Cannot Cover All Grades
Silicon carbide, chemical formula SiC, is a compound formed when carbon and silicon react at high temperature. Industrially it is produced by charging high-purity quartz sand together with a low-ash carbon source, most often low-sulphur petroleum coke, into a resistance furnace and driving the charge to the temperature at which the silica is reduced and the SiC lattice forms. The product combines a Mohs hardness of roughly 9.2 to 9.5, thermal conductivity closer to that of a technical ceramic than of an oxide refractory, strong resistance to oxidation, and a decomposition temperature above 2700 degrees Celsius under inert conditions.
Those properties explain the demand side. Silicon carbide serves as an abrasive, as a refractory raw material, as wear-resistant ceramic and blasting media, as a deoxidation and carburisation additive in steelmaking and cupola melting, and as a consumable in high-power electronics and semiconductor-related processing. The same properties also explain why silicon carbide is not traded as a single commodity. Abrasive-grade black SiC, high-purity green SiC, refractory-grade grain and metallurgical-grade SiC for iron and steel melting come out of related furnaces but are separated by crystal type, purity, particle size distribution and residual chemistry. Each of those attributes changes the yield recovered from a furnace campaign and the amount of crushing, screening, milling, magnetic separation and chemical washing needed to turn a crude ingot into a saleable lot. A quoted price is therefore only comparable when it is attached to a defined grade, a stated SiC content and a stated size specification.
Grades and Chemical Specifications of Silicon Carbide
Silicon carbide for abrasive and refractory duty is normally specified against GB/T 2480, which covers silicon carbide for these applications and is the reference most buyers use when drafting a purchase specification. Commercial supply concentrates on two crystal types, black and green, plus the lower-purity metallurgical material consumed by iron and steel melting shops. Headline SiC content is only the first line of the specification; the accompanying limits on free carbon, iron oxide, silica, free silicon, magnetic iron and moisture decide whether a lot is suitable for a given bond system, castable matrix or ladle addition.
| Product type | Typical SiC content | Crystal colour | Principal use | Usual supplied size range |
|---|---|---|---|---|
| Green silicon carbide, high purity | 99.0% and above | Green | Bonded and coated abrasives, precision lapping and polishing, fine ceramic consumables | Coarse grit to micrometre powders |
| Black silicon carbide, abrasive grade | 98.5% minimum | Black | Abrasives, blasting media, wear-resistant ceramics | Coarse grit to fine powder |
| Black silicon carbide, refractory grade | 90-97% | Black | Refractory bricks and castables, kiln furniture, non-ferrous melting crucibles | 0-1 mm, 1-3 mm, 3-5 mm and fines |
| Metallurgical silicon carbide | 60-90% | Black to grey | Deoxidation and carburisation in steelmaking, cupola and induction furnace melting | Lump 1-10 mm, briquettes, fines |
| Fine ceramic-grade powder | 97-99.5% | Black or green | Technical ceramics, seals, nozzles, sintering feedstock | Sub-millimetre to sub-micrometre |
Two lots carrying the same SiC figure can behave very differently in service. A black SiC lot at 98.5% SiC with elevated free carbon and magnetic iron is acceptable as a blasting medium but may discolour or weaken a vitrified bonded wheel, while a refractory castable depends heavily on silica and iron oxide levels because those oxides react with the matrix at working temperature. For metallurgical use, the value of the material depends on the ratio between SiC, free carbon and free silicon, because those three fractions describe how much silicon and carbon the addition actually delivers to the melt. Buyers should obtain a certificate of analysis per lot, not per annual grade, and should state the analytical methods they expect so that results are comparable between laboratories.
Physical and Thermal Properties That Drive Application Choice
Silicon carbide remains stable at temperatures where alumina-based refractories begin to creep, and it resists thermal shock far better than most oxide materials because of its high thermal conductivity and relatively low thermal expansion. These properties support its use in kiln furniture, burner nozzles, radiant tubes, crucibles for non-ferrous melting and wear linings in cyclone and chute applications where abrasion plus heat are present at the same time.
Mechanical performance depends strongly on how the ceramic is bonded. Recrystallised silicon carbide, nitride-bonded silicon carbide, oxide-bonded silicon carbide and reaction-bonded silicon carbide each trade strength, thermal conductivity and oxidation resistance against one another, and each one tolerates a different level of iron and free carbon in the starting grain. For abrasives, the controlling property is not bulk strength but grain toughness and friability. Green SiC is harder and more friable, which makes it preferable where a cool, free-cutting action and high surface finish are wanted, while black SiC is tougher and is preferred for rough grinding, blasting and heavy wear duties.
Particle Size, Screening Yield and Their Effect on Quoted Price
After the furnace ingot is crushed, the material is classified into size fractions. Only part of the crushed tonnage falls into the narrow bands that abrasive and refractory customers require, so the price of a specific grit carries the cost of the whole classification operation, not just the cost of the crude. Sizing is normally described with internationally recognised grit designations for coated and bonded abrasive applications, and with millimetre or mesh ranges for refractory and metallurgical grains. Sieve analysis certificates should be supplied with the lot, with the specification limits for the coarse, nominal and fine fractions stated explicitly.
Screening yield also explains why fine powders are usually more expensive per tonne than coarse grit of the same chemistry, and why a buyer who accepts a slightly wider size band can often be offered a better price. Magnetic separation efficiency, surface cleanliness and the absence of oversize particles that would score a workpiece all depend on the classification and finishing steps, so a size specification written too loosely will be met cheaply and a size specification written tightly will be met at cost.
Manufacture and the Cost Drivers Behind the Furnace
Silicon carbide is made in an Acheson-type resistance furnace. A mixture of quartz sand and carbon is built around a graphite core, current is passed through the core to raise the charge above the reaction temperature, and the furnace is then cooled before the ingot is stripped and the unreacted material is returned to the next charge. The high-grade material forms in the zone closest to the core; the outer skin is lower in SiC and is either downgraded or recycled. Green SiC is produced with a purer, lower-iron charge and often with additions that promote crystal growth, which is one reason green material commands a premium over black material of similar sizing.
Three inputs dominate the conversion cost. The first is the carbon source: petroleum coke quality, ash and sulphur content directly affect both the achievable SiC grade and the level of residual impurities. The second is the silica source, where iron and alumina content drive the purity ceiling of the finished grain. The third and usually the largest is electricity, because the furnace operates at very high power for a long cycle and the energy required per tonne of finished material is substantial; electricity commonly represents the single largest share of the ex-works conversion cost, so smelters located where industrial power is cheaper and more stable hold a structural advantage. Furnace capacity utilisation, the recovery of high-grade material from each campaign, and the yield of saleable sizing from the crude all follow from the same three inputs.
Metallurgical Silicon Carbide in Steelmaking and Foundry Practice
In iron and steel melting, silicon carbide is used as a combined source of silicon and carbon. Added to a ladle or to a melting furnace, it provides silicon for deoxidation and carbon for carburisation while generating far less silica load than a ferrosilicon addition, which matters where slag volume and slag chemistry are tightly controlled. In cupola melting, SiC briquettes and lump are added to raise the silicon content of the iron and to reduce coke consumption per tonne of hot metal, because the carbon in SiC is delivered to the melt with less loss than carbon charged as coke.
Metallurgical SiC is supplied as lump in defined size ranges, as briquettes of consistent mass, and as fines and powder for briquetting or injection. Typical commercial material falls in the 60-90% SiC range, with free carbon and free silicon making up much of the balance, and the material is usually purchased on the basis of the SiC content and the size fraction rather than on the basis of abrasive purity. Buyers should fix the sampling method, the analytical method for SiC and the tolerance for fines in the delivered lot, because fines handling losses are a real cost in this application.
Cost and Price Formation: The Variables That Move a Quotation
A silicon carbide quotation is assembled from several moving parts, and comparing quotations requires decomposing them into the same parts. The main variables are the grade and purity called for, the size fraction and its screening yield, the raw material and electricity cost at the producing plant, the treatment and finishing steps required, the packing and net weight offered, the delivery term, the currency, and the compliance and logistics cost of moving the goods to the destination.
On the raw material side, petroleum coke and quartz sand set a floor under conversion cost, and coke in particular transmits movements in fuel markets into SiC pricing with a lag, because furnaces are charged in campaigns rather than continuously. On the energy side, seasonal tariff structures, planned maintenance shutdowns, and the availability of lower-cost industrial power at a given smelter all influence the price a producer is willing to accept. Grade and sizing then determine what fraction of the furnace output can be sold as the premium product: a producer selling a large share of the crude as abrasive-grade grit and powder realises a higher average price than a producer selling most of it as refractory grain, and that difference shows up in the offer.
Quotation basis must always be compared like for like. Ex-works, FOB, CFR and CIF quotations are not interchangeable, because inland haulage, terminal handling, ocean freight, insurance and destination charges differ by port pair and by season, and incoterms such as FOB or CIF under the current Incoterms 2020 rules allocate loading, insurance and risk differently. Quotations should state whether the price includes value added tax and whether export documentation is included, and whether the packing is included in the net weight. Exchange rate treatment and the validity period of the offer are commercial terms that carry real value when raw material and freight markets are moving.
Specification Parameters to Fix Before Buying Silicon Carbide
A specification that arrives with complete parameters is quoted faster and more accurately. The following list covers the parameters that a producer needs before a firm offer can be made.
Product type and crystal colour: black or green, abrasive, refractory, metallurgical or ceramic grade.
SiC content with the required minimum, plus the maximum acceptable free carbon, iron oxide, silica, free silicon and moisture content.
Size specification: grit designation or millimetre range, with coarse and fine fraction limits and the acceptable oversize allowance.
Magnetic iron content limit and required magnetic separation treatment.
Packing: net weight per bag or drum, jumbo bag with or without liner, or bulk, and palletisation if required.
Quantity per shipment and expected annual volume, since campaign planning affects the offer.
Delivery term and destination, port of discharge, and required shipping documents.
Required analysis documents, sampling method and any third-party inspection arrangement.
Payment terms and offer validity period.
For metallurgical silicon carbide, add the intended addition method, whether briquette mass and strength are specified, and the maximum fines content at the receiving plant.
Inspection, Acceptance and Common Misunderstandings
Acceptance should be tied to a sampling plan agreed before shipment. For ferroalloy-type additions, sampling and sample preparation practice follows the general rules familiar to alloy buyers, and for silicon carbide the same discipline applies: draw increments from multiple positions in the lot, reduce the sample in a controlled way, retain a duplicate, and test the agreed parameters in a competent laboratory. Sieve analysis, moisture determination and chemical analysis should be reported on the same lot reference as the packing list so that results can be traced to specific bags or pallets.
Four misunderstandings recur in silicon carbide purchasing. The first is treating all 98.5% SiC material as equivalent when the accompanying free carbon, iron and size distribution differ. The second is buying on SiC content alone for refractory duty, where the oxide content governs service life. The third is comparing an FOB offer for coarse grit with a CIF offer for a fine powder and concluding that one supplier is cheaper. The fourth is ignoring the packing net weight, so that a quotation expressed per bag ends up materially different per tonne once the actual filled weight is checked at destination. Fixing grade, chemistry, size, packing and delivery term before comparing numbers removes all four problems.
Storage, Handling and Safety Notes
Silicon carbide is chemically stable and does not require special atmospheric protection, but fine powders should be kept dry and in closed packing, because moisture pick-up changes the reported moisture content and complicates weighing and feeding. Dust from handling fine grades is abrasive and should be controlled with local extraction during unloading and screening, and appropriate respiratory protection should be used where dust concentrations are high. Metallurgical lump and briquettes should be stored so that fines generated during handling are captured rather than lost, because fines content is a value parameter in that product line.
FAQ
Q: What is the difference between black and green silicon carbide?
Black silicon carbide is produced from a charge with higher iron and is tougher, so it suits rough grinding, blasting and wear-resistant applications. Green silicon carbide is produced from a purer charge, is harder and more friable, and is chosen where a cool cutting action and a fine surface finish are required.
Q: Which standard covers silicon carbide for abrasive and refractory use?
GB/T 2480 is the reference standard for silicon carbide in these applications, and it is normally cited together with grit designations recognised for coated and bonded abrasive products, so that both chemistry and sizing are defined.
Q: What SiC content should be specified for an abrasive grit?
Commercial black abrasive grit is generally offered at 98.5% SiC minimum, and green abrasive material at 99.0% SiC and above. The accompanying limits on free carbon, iron oxide and magnetic iron should be stated at the same time as the SiC figure.
Q: Why can two quotations for the same SiC content differ so much?
Because purity is only one dimension. Size fraction and screening yield, residual chemistry, magnetic separation treatment, packing net weight, delivery term and offer validity all change the price, and a quotation without those parameters is not comparable with another quotation.
Q: How is silicon carbide used in steelmaking?
It is added as a combined silicon and carbon source for deoxidation and carburisation. It delivers carbon to the melt with less oxidation loss than coke and generates a lower silica load than a ferrosilicon addition, which helps control slag volume and slag chemistry.
Q: What should be checked on a delivery of silicon carbide?
Check that the lot reference matches the certificate of analysis, that sieve analysis and moisture results fall within the agreed limits, that magnetic iron content is within specification, that packing net weights match the documents, and that the duplicate sample has been retained for any dispute.
Silicon carbide rewards a specification-led buying approach. Once the grade, SiC content, residual chemistry, size fraction, packing and delivery term are fixed in writing, the price comparison becomes a straight comparison of like with like, and the commercial risk of a shipment that fails in service largely disappears.

