The Discovery of Silicon Carbide: 1891 Furnace Experiment to Industrial Abrasive and Metallurgical Additive
Leave a message
1891: The Experiment That Produced Silicon Carbide
Silicon carbide entered industrial history in 1891. The American inventor Edward G. Acheson was attempting to synthesise diamond by heating a mixture of clay and coke powder inside an iron bowl, passing current through the charge with the bowl itself acting as one electrode and a carbon arc-lamp rod as the other. Instead of diamond he obtained bright green, extremely hard crystals growing on the carbon electrode. Acheson assumed the clay had yielded a new compound of carbon with alumina, and since the natural mineral form of alumina is corundum, he named the product carborundum. The material was in fact silicon carbide (SiC), formed when silica from the clay reacted with carbon at very high temperature.
The Chemistry and the Modern Furnace
The reaction Acheson observed is still the basis of production: silica (quartz sand) is reduced by carbon (petroleum coke or anthracite) in an electrically heated charge. The overall reaction is SiO2 + 3C = SiC + 2CO. In a modern Acheson-type resistance furnace the core reaches roughly 2,200 to 2,500 degrees Celsius, and a graphitised core carries current through a rectangular bed of mixed sand and coke for many hours. The furnace is then cooled for several days before the SiC ingot is broken out and crushed. Early plants were built next to cheap hydroelectric power, which is why the process became associated with locations such as the Niagara Falls area in the 1890s.
Why the Discovery Mattered
Silicon carbide was the first man-made abrasive, and its arrival changed metalworking, stone processing and glass grinding within a decade. With a Mohs hardness of about 9 to 9.5, it sits immediately below diamond and boron carbide, but it costs a fraction of diamond and can be produced in tonnage volumes. The same combination of hardness, thermal stability and chemical inertness later pushed SiC into refractories, wear parts, kiln furniture, semiconductor substrates and power devices, so the 1891 crucible experiment is now the origin point of a multi-industry material family.
Grades, Grain Sizes and Applicable Specifications
Fused silicon carbide is sold in two main abrasive grades: black SiC, produced from quartz sand with petroleum coke and used for bonded and coated abrasives as well as refractories, and green SiC, produced with a higher-purity silica and salt addition, which is harder and more friable and is preferred for grinding hard metals and cemented carbides. Grain size distribution of these fused products is standardised work: ISO 8486-1:1996 sets the method for determining and designating the size distribution of macrogrits from F4 to F220 in fused aluminium oxide and silicon carbide, while the companion part covers microgrits. Buyers managing bonded or coated abrasive lines should therefore specify grit by the F designation and demand the corresponding distribution certificate, rather than describing grit loosely as coarse or fine.
| Property | Typical value for fused SiC |
|---|---|
| Crystal form / hardness | Alpha-SiC, hexagonal; Mohs 9-9.5, Knoop hardness roughly 2,500 kg/mm2 on the basal plane |
| Density | About 3.1 to 3.2 g/cm3 |
| Thermal stability | Decomposes or sublimes above roughly 2,700 degrees Celsius; excellent thermal shock resistance |
| Chemical behaviour | Oxidises slowly in air above about 1,200 degrees Celsius forming a protective silica film; attacked by molten alkalis and some slags |
| Grain size standards | ISO 8486-1:1996 (macrogrits F4-F220); FEPA F grit designations for bonded and coated abrasives |
Metallurgical and Refractory Applications
Outside abrasives, the largest tonnage use is metallurgical. Silicon carbide works as both a silicon and a carbon carrier, so it is charged as briquettes or lumps for deoxidation and for silicon alloying, and it also improves the thermal balance of the furnace because the reduction reaction is exothermic in the melt. In refractories, SiC grain is used in blast-furnace trough castables, ladle and tundish linings, and blast-furnace wall sections where abrasion and thermal cycling dominate. Because SiC is electrically conductive, the supplier and the buyer must agree on grain size, SiC content and, for refractory grades, on the amount of free carbon and free silicon, since those factors change both oxidation behaviour and lining life.
Frequently Asked Questions
Q: Who discovered silicon carbide and when?
A: Edward G. Acheson in 1891, while he was trying to grow synthetic diamond in an electrically heated clay and coke charge. He named the crystals carborundum before the material was identified as SiC.
Q: Which standard defines abrasive silicon carbide grain sizes?
A: ISO 8486-1:1996 defines determination and designation of the grain size distribution of macrogrits from F4 to F220 in fused aluminium oxide and silicon carbide, and covers the F grit designations used for bonded and coated abrasives.
Q: What is the difference between black and green silicon carbide?
A: Black SiC is made from quartz sand and petroleum coke and is used in abrasives and refractories; green SiC is made with higher-purity raw material and is harder and more friable, so it suits grinding of hard metals and carbides.
Q: Is silicon carbide used in steelmaking, not only in abrasives?
A: Yes. SiC briquettes and lumps supply both silicon and carbon for deoxidation and alloying, and SiC grain is a common aggregate in taphole and ladle refractories where abrasion resistance matters.
Q: Does a silicon carbide purchase need a grain-size distribution certificate?
A: For abrasive use, yes. The grit must be ordered by the F designation and supported by a sieve analysis so that the delivered lot matches the distribution defined in ISO 8486-1:1996 for that grit number.
