Home - Knowledge - Details

Ferro Silicon Plasticity, Toughness and China Price Reference

What Determines Ferro Silicon Plasticity and Toughness

Ferro silicon is a master alloy smelted in a submerged arc furnace by reducing quartz with coke in the presence of iron-bearing scrap. Commercial material is graded by silicon content, and the most widely traded ladle-cast grades are FeSi75 and FeSi72 alongside lower grades such as FeSi65 and FeSi45. In the FeSi75 grade the silicon content is normally held between 72% and 80%, iron forms most of the balance, and aluminium, carbon, sulfur and phosphorus stay inside the limits of the applicable specification.

Cast ferro silicon is itself a hard and brittle intermetallic material. Its crystal lattice is dominated by strong Si-Si and Fe-Si bonds, so grains cannot slip freely under load and the ingot fractures rather than stretches. Bulk hardness is high and elongation is low, which is exactly why the alloy is crushed and screened to size instead of being formed. Ductility of the solid alloy therefore depends mainly on silicon content and on trace impurities: rising silicon raises hardness and reduces deformability, while lower silicon grades keep slightly better impact behaviour.

The plasticity that buyers of ferro silicon really care about belongs to the metal being treated, not to the alloy on its own. Added to molten steel, ferro silicon deoxidises the bath, lifts the silicon content and changes the way the metal solidifies. In ductile iron production a controlled ferro silicon addition, used together with a magnesium or rare-earth bearing treatment alloy, promotes spheroidal graphite, and the finished iron can reach 10% elongation or more at a tensile strength of 400-700 MPa. That combination of strength and ductility is where practical toughness is created.

Inoculation, Grain Refinement and Casting Soundness

Because silicon changes the way carbon precipitates from liquid iron, ferro silicon also works as an inoculant in grey and ductile iron foundries. Inoculation multiplies the number of graphite nucleation sites, refines the graphite morphology and suppresses chill and carbide formation. A finer and more uniform structure lowers internal stress concentrations, which appears as better fatigue life and higher impact energy in the finished casting.

Typical inoculation additions are 0.1-0.5% of the charge weight, introduced into the ladle or into the pouring stream. Particle size is matched to the treatment method: 3-10 mm for late stream inoculation, 10-50 mm for ladle additions and 10-100 mm for furnace side charging. Oversized lumps dissolve too slowly, dusty fines dissolve too quickly, and both give erratic recovery and inconsistent chemistry in the casting.

In steelmaking the deoxidation reaction removes dissolved oxygen and forms a silicate slag that floats to the bath surface. Aluminium in the alloy is deliberately controlled, because it strongly affects steel cleanliness. Grades with a guaranteed low aluminium content are therefore chosen for continuously cast and drawing quality steel, where coarse oxide inclusions would cause surface defects or wire breaks.

China Ferro Silicon Price Reference

Manufacturer offers and transaction values for 75 grade ferro silicon across the main Chinese production regions are summarised below. All figures are stated in CNY per metric ton and reproduce the published market snapshot dated 29 May 2023; a negative change means the quotation moved lower than the previous assessment.

Region Grade Manufacturer offer Change Transaction price Change
Inner Mongolia 75 7650-7750 -100 7650-7700 -75
Ningxia 75 7650-7750 -100 7600-7700 -100
Gansu Province 75 7650-7750 flat 7600-7700 flat
Qinghai 75 7600-7800 flat 7600-7700 flat
Shaanxi 75 7600-7700 -100 7600 -50

Northwest China dominates domestic capacity because quartz, carbon reductants and comparatively cheap power are available in the same region. Inner Mongolia, Ningxia, Gansu, Qinghai and Shaanxi together account for the majority of national output, and their quotations usually define the reference level that other provinces follow. The furnace is power intensive, so a change in electricity tariffs or in coke prices is reflected in the offer level within days, and the spread between manufacturer offers and transaction prices widens whenever demand from steel mills softens.

Quality Assurance for Consistent Recovery

Optical emission spectrometry on every heat, reporting silicon, carbon, aluminium, sulfur and phosphorus rather than silicon alone.

Screened size fractions of 3-10 mm, 10-50 mm and 10-100 mm, with fines content controlled so that dissolution behaviour stays predictable.

Structure and hardness checks that confirm the material is fully alloyed and free of slag inclusions or unmelted quartz.

Moisture-controlled storage, because damp fines can react violently when they meet liquid metal.

Silicon recovery in the ladle normally settles between 85% and 95% when sizing and addition practice are matched to the treatment method. Recovery falls when the alloy is charged too early, when the particle size is too fine, or when the material is stored in damp conditions. Tracking recovery heat by heat is the most reliable way to confirm that a supplier is holding its declared chemistry over a long campaign.

Frequently Asked Questions

Q: Is ferro silicon plastic or brittle?
Cast ferro silicon is hard and brittle, because its lattice resists grain slip. The ductility that is associated with ferro silicon belongs to the steel or cast iron that has been treated with it.

Q: Does a higher silicon grade make the treated metal tougher?
Only indirectly. Silicon content determines how much silicon is delivered to the bath, while toughness comes from the graphite or carbide structure that forms during solidification, so grade choice and addition practice must be considered together.

Q: Which grade is used for steel deoxidation?
FeSi75 is the usual choice for general deoxidation, while low aluminium grades are specified for continuously cast and drawing quality steel where inclusion control is critical.

Q: What particle size should be ordered for inoculation?
Use 3-10 mm for late stream inoculation, 10-50 mm for ladle additions and 10-100 mm for furnace side charging, keeping fines to a minimum.

Q: Why do Northwestern Chinese smelters set the reference price?
The region combines quartz, reductant and low cost power, so its production costs are the lowest in the country and its offers anchor the quotations reported for other provinces.

Q: How much ferro silicon is consumed per ton of treated iron?
Inoculation normally consumes 0.1-0.5% of the charge weight, while deoxidation additions depend on the oxygen content of the heat and are calculated from the carbon and silicon balance of the melt.

Send Inquiry

You Might Also Like