Different Forms of Ferrosilicon: Lumps, Granules and Powder Explained
Leave a message
What Ferrosilicon Is
Ferrosilicon is an iron silicon alloy smelted in a submerged arc furnace from quartz or silica sand, a carbon reductant such as coke, and iron bearing charge in the form of steel scrap or mill scale. Silicon content covers a wide range, and standard grades run from about 15% through 45%, 65% and 72% up to 75%. The alloy is used mainly in the iron and steel industry, where it acts as a deoxidiser, an alloying addition, an inoculant and a desulfurising aid, and its cost per unit of silicon makes it economical in each of those duties.
Forms of Ferrosilicon: Lumps, Granules and Powder
The same alloy is delivered in three basic physical forms, and the choice depends on how the addition has to dissolve and where it has to be placed.
| Form | Typical size | Main use |
|---|---|---|
| Lump | 10-100 mm, usually split 10-50 mm or 50-100 mm | furnace and ladle charging, bulk deoxidation |
| Granule | 0.2-2 mm, 1-3 mm or 3-8 mm | continuous addition, wire injection, inoculation |
| Powder | below 75 µm, typically -200 mesh | heavy media suspensions, welding flux and briquette feed |
Lumps have low dust and dissolve slowly, which suits large heats where the addition has to reach the bottom of the bath. Granules flow through feeders and injection wires and dissolve quickly. Powder is used where the alloy has to be carried in suspension or bonded into another product rather than charged in bulk.
Grades and Typical Composition
Ferrosilicon is normally ordered against GB/T 2272, with silicon, aluminium, carbon, sulphur, phosphorus and size declared per lot. Low aluminium grades are specified where the residual aluminium in the finished steel has to be kept low.
| Grade | Silicon, typical | Typical duty |
|---|---|---|
| FeSi75 | 74-80% | inoculation and alloying of electrical and heat resistant steels |
| FeSi72 | 72-80% | deoxidation and foundry additions |
| FeSi65 | 65-72% | deoxidation and slag conditioning |
| FeSi45 | 40-47% | general deoxidation and casting additions |
| FeSi15 | 14-16% | heavy media suspensions for coal and mineral separation |
Choosing the Right Form
Inoculation of grey and ductile iron: FeSi75 low aluminium lump or granule sized to dissolve before solidification.
Ladle or furnace deoxidation: lump FeSi72 or FeSi65 charged with the scrap or released into the tap stream.
Alloying of silicon, electrical and heat resistant steels: FeSi75 or FeSi65.
Desulfurisation and slag conditioning: FeSi65 or FeSi45, often with lime or calcium bearing additions.
Heavy media separation: fine FeSi15 powder milled to about -200 mesh and held in suspension.
Welding consumables and briquetted feed: fine powder sized for the coating or briquetting line.
Handling, Packaging and Quality Control
Ferrosilicon is packed in 25 kg or 50 kg bags, in 1 t big bags or in bulk, and powder is packed in moisture barrier liners. Storage must stay dry and ventilated: damp ferrosilicon fines can release hydrogen and phosphine, which is both a fire and a health hazard, so enclosed spaces are tested before entry and dust is controlled at transfer points. Incoming lots are checked for silicon, aluminium, carbon, sulphur and phosphorus content and for size distribution, and the furnace charge is adjusted accordingly.
Because lump ferrosilicon is not hygroscopic but the fines are, good practice is to keep powder lines separate, use sealed liners, and rotate stock so that nothing sits in a damp store. The quality risks seen most often in practice are aluminium above the agreed limit, excessive fines in a lump order and moisture in a powder order.
Frequently Asked Questions
Q: Why is ferrosilicon used as an inoculant in cast iron?
It provides a controlled silicon addition at the right moment to promote graphite nucleation, which refines the structure, improves the form of the inclusions and raises the quality of the finished casting.
Q: What is the difference between ferrosilicon lump and ferrosilicon powder?
Lump material is charged in bulk and dissolves over time, while powder is used in suspension, in welding flux coatings or in briquettes where the alloy must be dispersed rather than charged.
Q: What are the standard ferrosilicon grades?
The usual grades are FeSi75, FeSi72, FeSi65, FeSi45 and FeSi15, ordered against GB/T 2272 with silicon, aluminium, carbon, sulphur and phosphorus declared per lot.
Q: How does ferrosilicon deoxidise steel?
Silicon has a high affinity for oxygen, so it combines with dissolved oxygen in the liquid steel and removes it as a silica rich slag, which reduces gas porosity and improves the cleanliness of the steel.
Q: Which ferrosilicon grade is used for heavy media separation?
Fine FeSi15 powder, milled to about -200 mesh and suspended in water, is used to prepare the dense medium that separates coal and minerals by specific gravity.
Q: How should ferrosilicon be stored?
Keep it dry and ventilated. Lumps tolerate normal covered storage, but fines must be kept in sealed moisture barrier packaging because damp fines can release hydrogen and phosphine.
