Cafe Calcium Ferro Cored Wire
Application: spheroidizing wire/inoculation wire/spheroidizing cored wire/casting steelmaking
Packing method: horizontal and vertical, the cable can be divided into internal tap and external type.
Description
ZhenAn International Co., Limited is one of the most reliable manufacturers and suppliers of cafe calcium ferro cored wire in China. With abundant experience, we warmly welcome you to wholesale discount cafe calcium ferro cored wire in stock here from our factory. Quality products and reasonable price are available.
Cafe Calcium Ferro Cored Wire Description
Cafe calcium ferro cored wire is a product that improves the quality of steelmaking, and its varieties are increasing day by day. Pay attention to details when choosing products and avoid purchasing low-quality core wires. So what are the precautions for operating cored wire?
1. Reasonably adjust the feed speed. The absorption rate of calcium is greatly affected by the feeding speed. Too fast or too slow will reduce the absorption rate. When the earth's core reaches a certain depth, the earth's core begins to melt. It is necessary not only to ensure the melting and dispersion of deep calcium bubbles, but also to withstand the large static pressure of molten steel so that the calcium bubbles are completely consumed in advance.
2. Floating on the surface of steel. Reasonable dosage can improve calcium recovery rate. If the speed is too fast, on the one hand, a large amount of calcium vapor will be generated locally, causing the molten steel to be violently stirred, and a large amount of calcium vapor to volatilize directly into the air. On the contrary, too much calcium vapor floats and cannot be dissolved, which will reduce the yield of Baotou rare earth silicon alloy. On the contrary, if the feeding depth is not enough, it will rise to the surface of the molten steel before it is completely dissolved in the molten steel, causing waste.
3. The wire feeding position must be accurate. Feeding patterns also have an important influence on calcium recycling. In the center of the downward flowing molten steel, it should be as far away from the argon blowing bright circle as possible to make Ca turn into gas or liquid. Since Ca is a gas or liquid, it will decrease when flowing downward, thereby prolonging its residence time in the molten steel and being completely absorbed by the molten steel.
Cafe Calcium Ferro Cored Wire Specification
|
Name |
Casi alloys cored wire |
|
Wire Dia. |
13mm |
|
Steel Thickness |
0.4±0.05mm |
|
Powder contain: |
225g/m ±10g/m |
|
Coil I.D. |
600mm |
|
CoIil O.D. |
1100mm |
|
Coil Height |
1100mm |
|
Alloy Type |
CaSi, Ca (Pure Calcium), CaFe, CaAlFe, Mg, FeSi , FeSiMg |
What is the daily maintenance method for cafe calcium ferro cored wire?
1. Core-clad wire should be purchased and installed in a place where the local ambient temperature is lower than 50 degrees Celsius.
2. The appearance and interior of the cored wire purchasing box should always be kept dry and clean. In particular, waterless compressed air should be used to blow away the dust in the box and power distribution cabinet to control the appearance.
3. Do not press the power switch to control the appearance for no reason.
4. The sensor should be protected regularly (once a week) to remove magnetic dust adsorbed on the counting magnet and sensor.
5. After the wire feeding operation is completed, all power supplies should be turned off, and be careful not to energize the inverter and other electrical appliances. This can increase the safety of the equipment and the service life of the electrical appliances, especially the inverter.
6. Check the following parts before taking over: the upper and lower wire feed wheels must not be loose. When taking over, check whether the electrical part operates reliably.
7. Add lubricating oil to the following parts as specified.
8. The transmission chain should be lubricated once a week, and the manual worm gear, connecting rod pin, and slider should be lubricated once every shift.
Cafe Calcium Ferro Cored Wire FAQ
Q: Are you a trading company or a manufacturer?
A: we are a manufacturer located in Anyang City, Henan Province,China. All our customers come from home and abroad. Looking forward to your visit.
Q: How long is your delivery time?
A: Generally 5-10 days if the goods are in stock, 15-20 days if the goods are not in stock. It is according to the order quantity.
Q: Do you provide free samples?
A: Yes, we could offer the free sample, you only need to pay the freight.
Hot Tags: cafe calcium ferro cored wire, China cafe calcium ferro cored wire manufacturers, suppliers, factory, High Quality Cast Iron Cored Wire Calcium Silicon Core Wire, Calcium Cored Wire Deoxidizer CaSi, Calcium Silicon Cored Wire, High Purity Calcium Silicon CaSi Cored Wire for Steelmaking, Calcium Silicon Cored Wire Of High Quality, Calcium Silicon Ca30Si60 Ca30Si50 Cored Wire
Send Inquiry
You Might Also Like
